Drivers y manuales

Original Prusa i3 MK3

RSS

Firmware 3.4.1 4 de octubre de 2018

Descargar 3.4.1 (7MB)

Cambios en la 3.4.1

  • Filament runout detection fixed
  • Stealth mode bug (indicated as slow Z-axis movements) fixed
  • Message "Filament sensor response is poor, disable it?" has been temporarily disabled - this feature tended to be too sensitive and unreliable. We are working on improved version of this feature.
  • Statistics during active print fixed
  • OctoPrint "Printer reset detected" warning issue fixed

Drivers & Apps 2.2.1 27 de octubre de 2018

Cambios en la 2.2.1

  • Slic3r 1.41.1
    • Custom supports - support blocker & enforcer modifier meshes
    • Improved quality of supports
    • Multi Material fixed and improvements
    • Bug fixes - see full changelog below
  • MK2.5 MMU2 Support
  • MK2.5 MMU2 G-codes
  • Added a link to New User Guides at the end of the installation

Handbook 3.04 30 de octubre de 2018

Descargar (8MB)

Cambios en la 3.04

  • Loading filament (updated chapter)
  • LCD screen (updated chapter)
  • Beeper settings (new chapter)
  • Language settings (new chapter)
  • MMU 2.0 (new chapter)
  • Slic3r PE (updated chapter)
  • Filament sensor (updated chapter)
  • Updating firmware (updated chapter)
  • Linearity correction (new chapter)

Original Prusa i3 MK2.5

RSS

Firmware 3.4.1 4 de octubre de 2018

Descargar 3.4.1 (7MB)

Cambios en la 3.4.1

  • Filament runout detection fixed
  • Silent mode bug (indicated as slow Z-axis movements) fixed
  • Message "Filament sensor response is poor, disable it?" has been temporarily disabled - this feature tended to be too sensitive and unreliable. We are working on improved version of this feature.
  • Statistics during active print fixed
  • OctoPrint "Printer reset detected" warning issue fixed

Drivers & Apps 2.2.1 27 de octubre de 2018

Cambios en la 2.2.1

  • Slic3r 1.41.1
    • Custom supports - support blocker & enforcer modifier meshes
    • Improved quality of supports
    • Multi Material fixed and improvements
    • Bug fixes - see full changelog below
  • MK2.5 MMU2 Support
  • MK2.5 MMU2 G-codes
  • Added a link to New User Guides at the end of the installation

Handbook 2.5 2 de marzo de 2018

Descargar (7MB)

Cambios en la 2.5

Initial version

Original Prusa i3 MK3/MK2.5 Multi Material 2.0

RSS

Firmware 3.4.2 (V1.0.2) 20 de octubre de 2018

Descargar 3.4.2 (V1.0.2) (14MB)

Cambios en la 3.4.2 (V1.0.2)

This firmware version is specifically for users who use MK2.5 + MMU2 setup. If you are not using MMU2 or if you use MMU2 with MK3 printer it is not necessary to upgrade to this version.

  • MK2.5 + MMU2 setup loudness reduced - For corrent beahviour it is necessary to use MMU firmware 1.0.2 and higher when running MMU2 with MK2.5. Users who use MK3 printer do not need to upgrade their MMU2 firmware.
  • MK2.5 + MMU2 setup initialization - MK2.5 was unable to automatically detect MMU2 unit after turning on the printer. This has been fixed.

Drivers & Apps 2.2.1 27 de octubre de 2018

Cambios en la 2.2.1

  • Slic3r 1.41.1
    • Custom supports - support blocker & enforcer modifier meshes
    • Improved quality of supports
    • Multi Material fixed and improvements
    • Bug fixes - see full changelog below
  • MK2.5 MMU2 Support
  • MK2.5 MMU2 G-codes
  • Added a link to New User Guides at the end of the installation

Handbook 1.0 30 de agosto de 2018

Descargar 1.0 EN (5MB)

Cambios en la 1.0

  • Initial MMU 2.0 release

MK3/MK2.5 Multi Material 2.0  manual en otras versiones:
Čeština (v1.01) | English (v1.01)

Manual de montaje del kit
Versiones anteriores

Firmware 3.1.0 12 de noviembre de 2017

Descargar 3.1.0

Cambios en la 3.1.0

  • Linear Advance
  • Wizard
  • Host keep alive messages – better OctoPrint compatibility
  • Sorting files in SD card menu by date or name
  • Check if file is complete
  • First layer calibration – V2 integrated into FW
  • Auto power mode
  • XYZ calibration details menu improved
  • PID calibration safety check
  • M220: Speed factor
  • Saving E steps per mm to EEPROM fixed
  • Long filename scrolling is improved
  • Read more about this major version at prusaprinters.org
  • There’s a known bug using Repetier server, please wait for the next release if you’re using it

Drivers & Apps 2.2.1 27 de octubre de 2018

Cambios en la 2.2.1

  • Slic3r 1.41.1
    • Custom supports - support blocker & enforcer modifier meshes
    • Improved quality of supports
    • Multi Material fixed and improvements
    • Bug fixes - see full changelog below
  • MK2.5 MMU2 Support
  • MK2.5 MMU2 G-codes
  • Added a link to New User Guides at the end of the installation

Firmware 3.1.0 12 de noviembre de 2017

Descargar 3.1.0

Cambios en la 3.1.0

  • Linear Advance
  • Wizard
  • Host keep alive messages – better OctoPrint compatibility
  • Sorting files in SD card menu by date or name
  • Check if file is complete
  • First layer calibration – V2 integrated into FW
  • Auto power mode
  • XYZ calibration details menu improved
  • PID calibration safety check
  • M220: Speed factor
  • Saving E steps per mm to EEPROM fixed
  • Long filename scrolling is improved
  • Read more about this major version at prusaprinters.org
  • There’s a known bug using Repetier server, please wait for the next release if you’re using it

Drivers & Apps 2.2.1 27 de octubre de 2018

Cambios en la 2.2.1

  • Slic3r 1.41.1
    • Custom supports - support blocker & enforcer modifier meshes
    • Improved quality of supports
    • Multi Material fixed and improvements
    • Bug fixes - see full changelog below
  • MK2.5 MMU2 Support
  • MK2.5 MMU2 G-codes
  • Added a link to New User Guides at the end of the installation

Firmware 3.1.0 12 de noviembre de 2017

Descargar 3.1.0

Cambios en la 3.1.0

  • Linear Advance
  • Wizard
  • Host keep alive messages – better OctoPrint compatibility
  • Sorting files in SD card menu by date or name
  • Check if file is complete
  • First layer calibration – V2 integrated into FW
  • Auto power mode
  • XYZ calibration details menu improved
  • PID calibration safety check
  • M220: Speed factor
  • Saving E steps per mm to EEPROM fixed
  • Long filename scrolling is improved
  • Read more about this major version at prusaprinters.org
  • There’s a known bug using Repetier server, please wait for the next release if you’re using it

Drivers & Apps 2.2.1 27 de octubre de 2018

Cambios en la 2.2.1

  • Slic3r 1.41.1
    • Custom supports - support blocker & enforcer modifier meshes
    • Improved quality of supports
    • Multi Material fixed and improvements
    • Bug fixes - see full changelog below
  • MK2.5 MMU2 Support
  • MK2.5 MMU2 G-codes
  • Added a link to New User Guides at the end of the installation

Handbook 1.05 16 de octubre de 2016

Descargar (6MB)

Cambios en la 1.05

  • PEI surface preparation changes
  • calibration flow tweaks, when is needed to redo the calibration
  • how to change filament during a print
  • dental floss for object removing
  • light and full factory reset
  • firmware update

Firmware 3.0.12 23 de junio de 2017

Descargar 3.0.12

Cambios en la 3.0.12

  • Calibración XYZ mejorada
  • Los resultados de la calibración XYZ están disponibles en el menú Support
  • Selftest arreglado
  • Mejorada la descarga de filamentos
  • Multi Material
  • Cuando se para una impresión, se pregunta que filamentos se quieren descargar
  • Añadido gcode “T?”, el cual selecciona a priori el extrusor a usar para la impresión
  • Añadido soporte para MK1

Drivers & Apps 1.7.7 6 de mayo de 2017

Cambios en la 1.7.7

Slic3r PE upgraded to 1.34.1 – Up to 4x faster slicing thanks to parallelization

Other downloads

RAMBo addon para Arduino

  • Permite a Arduino IDE cargar FW. Si puedes usar nuestro FirmwareUpdater y archivos hex.
  • Download

ColorPrint

Ajustes Cura

Ajustes Simplify3D

MK2 MMU V2 CALIBRATION

MK2/S V2 CALIBRATION

MMU Post Processor

  • Only for MMU 1 (not compatible with MMU 2.0)
  •  Download